August 19, 2008

No

Picture

Available

Rotary #1441

Reichdrill T-690 Year: 2006 Cat electronic; Compressor: 1070-350; Mounted On: Mack; TrEngine: 2006; Tools/Other Options: 1000' drill rod, heavy hoist, regen system, 20 gal water injection, remote helpers controls, 2 speed winch control, 1000 hrs on drill, 3,000 miles on truck, like new.

Rotary #1439

Reichdrill T-650 WS Year: 1985 3406; Compressor: 800-325; Mounted On: mack; TrEngine: 1985; Tools/Other Options: 4 jacks, 750' drill rod 4 1/2 x 20'.

No

Picture

Available

Rotary #1444

Reichdrill T-650 W 11 Year: 1999; Compressor: 850-350; Mounted On: Int; TrEngine: 1999.

Rotary #1445

Reichdrill T-650-W Year: 1985 2406; Compressor: 8250300; Mounted On: Int; TrEngine: 1985.

No

Picture

Available

Auger #1440

Simco 5000 Year: 1979 gas; Compressor: ; Mud Pump: 3 x 4 mission; Mounted On: Ford 9000; TrEngine: , 3406; Tools/Other Options: 10,000 lb main winch and sand line 2" air operated wylden grout pump, 15' rod rack, with 280' 3 1/2 x 15' dril rods 2 3/8 thread, and stablizer, mounted on ford 9000, 10 speed road ranger.

No

Picture

Available

Water Truck #1442

Mounted On: Mack; TrEngine: 335 hp; Tools/Other Options: 2000 gal water , hendrickson walking beam, truck has new been stuck, good rubber, 6 good size boxes, holds 130 gal fuel, nfuel pump has air driven transfer pump, retractable hose reel, bed 23' long, clear title, low hrs.

Cable #1443

Smeal 5-Tt Mounted On: GMC Topkick; TrEngine: 1991, Cat Diesel; Tools/Other Options: Main line, sand line, remote and pipe racks, truck is 22,000GVW, miller welder. No rust.

Rotary #1446

Mayhew 1000 Mud Pump: G.D. And 4 x 3 also; Mounted On: Mack; TrEngine: 1995; Tools/Other Options: 2 jack, 13 M drawworks, 32' derrick, 300' drill rods, 1 5 1/4 bit 1 7 3/4 bit little giant swivel..hyd chain pull down.

Rotary #1447

Chicago Pneumatic T-650 Year: 1982 3406; Compressor: 825-300; Mounted On: Int; TrEngine: 1982, dt 466; Tools/Other Options: 800' drill rod, compressor just rebuilt o time, engine rebuilt 2000 hrs ago, rebuilt head, new rear end rebuilt, rebuilt pulldown cylinders.

Rotary #1448

Green Manufacturing 2500 series Year: 300 ford propane; Mud Pump: 4 x 5 centrifical; Mounted On: GMC 9500; TrEngine: , 6 V 92; Tools/Other Options: shallow oil and gas rig, 18" rotary table air activated, direct drive double drum drawworks, 52' mastnew diamond plate floor, 6" by 40ft king swival kelly, worklights, 9 speed, 600' of 4 1/2 x 31' drill rod, 1 31'73/4odx21/2id drill collar, rig comes with all the make up tools to drill there is a 40' float this is a complete package.

July 24, 2008

Rotary #1433

Drilltech D-25 Year: 1997 Cat 3406; Compressor: 900-350; Mounted On: Ford; TrEngine: 1997, 300 hp; Tools/Other Options: pullback 30,000, 28' head travel, pipe rack for 15 pc. 20' drill rods 520', pipe loader, auxiliaryremote controk station, jib boom with hyd extend with 180 swing, winch is 7,500 lb drill table 20' opening with hyd adjustment, breakout with 48" jaw type, night lights, fine feed for torque control, lubricator with 10 gal tankll Year: 1978; Compressor: 250 x 125; Mud Pump: 5 x 6 GD; Mounted On: Ford; TrEngine: 1978, 3208; Tools/Other Options: 200' drill rod, all slip and bushings.

Rotary #1435

Ingersoll Rand T-4 Year: 1985 V-12; Compressor: 900-300; Mounted On: CCC; TrEngine: 1985, 3208; Tools/Other Options: 70,000 lb machine 1,500' drill rods, 6" and 8" hammers, new chains and sprockets, v-12 new used.

July 18, 2008

Rotary #1437

Ingersoll Rand T-3 W Year: 1995, 3406 Cat; Compressor: 900-350; Mounted On: Ford; TrEngine: 1995; Tools/Other Options: 520' drill rods, 6" hammer, 8" hammer, 1000 hrs on deck engine, 25 gal water injection.

Cable #1438

Wichtex T.E. 2 work over rig Year: 478 GM; Mounted On: Ford 600; TrEngine: 1976, 371 Ford; Tools/Other Options: 2 cat heads, propane powered, 35' 65/8 double pole mast, with screw type levling jacks. Double drum draworks, main drum has double sleeve block, sandline has 860' cable.

July 16, 2008

Rotary #1434

Gus Pech H-48 super george Year: 1977 391; Mounted On: Mack; TrEngine: 1977, 300; Tools/Other Options: 35' mast with 100' 4 stage x 25' foot kelly, plus 25' ext. 48" turntable, main winch is 14,000 lbs pull. Sand winch 9000 lbs pull. 3 jacks, 24' and 36' buckets with machine, bucket will ream to 48'.

Rotary #1436

Year: 1986 v-6 detroit; Compressor: 600-350; Mounted On: Ford; TrEngine: 1986, ford diesel; Tools/Other Options: 15,000 miles on truck, 4,500 hrs on rig, 240' drill rod.

July 05, 2008

No

Picture

Available

Rotary #1428

Chicago Pneumatic T-650 SS Explorer Year: 1982 3406 Cat; Compressor: 825-300 GHH; Mounted On: CCC; TrEngine: 1982, Cat; Tools/Other Options: 500' drill rods 4 1/2 x 20'.

Rotary #1429

Ingersoll Rand T-4 Year: 1991 Cummins; Compressor: 1050-350; Mounted On: CCC; TrEngine: 1991; Tools/Other Options: 70,000 pullback machine,Rebuilt KTA Cummins 19 C engine, water injection, updated Hyd. Drill ready.

Rotary #1431

Foremost DR-24; Mounted On: CCC.

Rotary #1432

Foremost DR-40; Mounted On: Crawler.

Rotary #1430

Drilltech D-25 Year: 1987 ; Compressor: 840-350; TrEngine: 1987; Tools/Other Options: 300' drill rod, compressor has low hrs.

Rotary #1433

DSI QuickdriDrilltech D-25 Year: 1997 Cat 3406; Compressor: 900-350; Mounted On: Ford; TrEngine: 1997, 300 hp; Tools/Other Options: pullback 30,000, 28' head travel, pipe rack for 15 pc. 20' drill rods 520', pipe loader, auxiliaryremote controk station, jib boom with hyd extend with 180 swing, winch is 7,500 lb drill table 20' opening with hyd adjustment, breakout with 48" jaw type, night lights, fine feed for torque control, lubricator with 10 gal tankll Year: 1978; Compressor: 250 x 125; Mud Pump: 5 x 6 GD; Mounted On: Ford; TrEngine: 1978, 3208; Tools/Other Options: 200' drill rod, all slip and bushings.

June 11, 2008

Rotary #1408

Speedstar SD 600 Year: 1985; Compressor: 600 x 250; Mud Pump: 5 x 6 GD; Mounted On: Ford; TrEngine: 1985, 400 cummins; Tools/Other Options: 300' drill rods, 4 jacks.

May 01, 2008

Cable #1410

Stone 31; Mounted On: Ford; TrEngine: 1978, 6 cyl ford.

April 09, 2008

Rotary #1427

Ingersoll Rand RD-20 Year: 2006; TrEngine: 2006; Tools/Other Options: Condition: low hrs.

Rotary #1426

Ingersoll Rand RD-20 Year: 2005; TrEngine: 2005.

April 02, 2008

Rotary #1425

Jaswell 3500 Year: 1980; Mounted On: Int Paystar 5000; TrEngine: 1980; Tools/Other Options: 3000' drill rod, 70,000 lbs pullback, 150/1600 aux air with GD booster, all hyd rebuilt, top head rebuilt, new dennison pump, new Schramm floating sub, generator.

Rotary #1424

Kremco L-600 Year: 1981 detroit 12 V 71; Tools/Other Options: 230,000 lb hook-load capacity on 8 line traveling block, 103' GL to crown, range 111 casing, hy service winch, 7000' drill rod. 2 3000 psi bop's , generator set, fuel water trailer, 2 skid mounted IR / keystone air compressors, 1 air booster JGQ-2, 17 1/2 rotary table with master bushing, mud pump P-214 duplex, washington air rotating head.

Water Truck #1421

Mobile vacuum Mounted On: Autocar truck; TrEngine: 290 Cummins; Tools/Other Options: 13 speed transmission, large heavy duty compressor, vaccum and discharge capability, tank is fitted with hydraulic lift system, rear of tank is fitted with hydraulic opening system, the entire back or tank opens via hydraulics for easy cleanout.

No

Picture

Available

Rotary #1416

Reichdrill T-650 SAM Year: 1989 Cummins; Compressor: 840-350 GHH; Mounted On: Int.; TrEngine: 1989, diesel; Tools/Other Options: 10 speed, new tires, 1800 RPM, dual head motors, water injection, oiler, new chains, 50,000 lbs pullback, SAM drill.

Rotary #1413

Chicago Pneumatic T-650w Year: 250 HP Cat; Compressor: 450/250 CP; Mounted On: Kenworth; TrEngine: 1989, 400 HP Cat; Tools/Other Options: 300' OF 4.5 x 20' Drill Pipe, 9 gpm Bean duplex inj. Pump, all hand tools, table bushing, Bob Cat 225 miller welder with cables, rod sling, night lighting, line oiler (air), 4000#, 20,000# front end jake brake, 46,000# rear (double lock-ups),Mudgrip tires on rear, spare tire carrier behind cab, rack for carrying chuck blocks.

Rotary #1412

Portadrill TKS Year: 1978 Detroit 8V92T; Compressor: Sullair 2012 750/250; Mounted On: Int. 5050; TrEngine: 1977, 3208; Tools/Other Options: Double drum drawworks, 38' steel mast, Deck mounted compressor, bean water injection, 7-1/2" rotary table, 45,000# swivel, 4.5" X 22.5" round sloted kelly. Truck engine has 20,525 original miles. Deck engine approx. 4000 hours.

Rotary #1415

Gardner Denver 1000 Heavy Duty; Compressor: 667 GD; Mud Pump: 5X6 GD; Mounted On: Mack; TrEngine: 235 hp Diesel; Tools/Other Options: Bean Injection Pump, Rebuilt & customized in 2001, 1000 rotary table with 5 speed transmission, 1250 air-clutched draw-works, 4 speed hydraulic pull-down,2 hydraulic leveling jacks, pipe rack with slide.

Rotary #1417

Gardner Denver 1000 Heavy-Duty; Compressor: 580 GD; Mud Pump: 5X6; Mounted On: Mack Truck; TrEngine: 285 hp Mack; Tools/Other Options: Newly rebuilt & customized, hydraulic pull-down, 23' Kelly, 1250 air clutched draw-works, 5-1/2" 1000 rotary table, heavy duty swivel, pipe rack with slide, 2 hydraulic leveling jacks.

Rotary #1420

Gardner Denver 1000 Heavy Duty; Compressor: 667 GD; Mud Pump: 5X6; Mounted On: Mack Truck; TrEngine: 285 hp; Tools/Other Options: Fully refurbished, 1000 rotary table, 1250 air draw-works, hydraulic pull down, 2 hydraulic leveling jacks, pipe rack with slide.

Rotary #1422

Gardner Denver; Compressor: 50 S-1 LeRoi; Mud Pump: 5X6; Mounted On: Ford Diesel 4X4; TrEngine: 8.2L Detroit; Tools/Other Options: Engine overhauled, 5 speed transmission with auxiliary and heavy duty transfer case, 4 cyl Bean Inj. Pump. IDEAL FOR ALL-TERRAIN ENVIRONMENTAL, compact & custom rotary rig modified for A-T drilling, 5-1/2" rotary table, 13' kelly (10' drill pipe), 1250 air clutched draw works, 2 hydraulic leveling jacks, double framed chassis, floatation tires, front mounted Ramsey winch, pipe rack with slide. Rebuilt 2002.
MATCHING WATER TRUCK INCLUDED.

April 01, 2008

Auger #1411

AMS Envirodrill Year: 1996 42 HP Teldyne; Mounted On: Custom Built Trailer; TrEngine: , ; Tools/Other Options: 3 leveling jacks, direct push hammer as well as a rotary drill head. Have installed 65' 2" diameter MW's with it.

Rotary #1418

Badger 1250 Compressor: 100 S-1 LeRoi; Mud Pump: 5X6; Mounted On: Int. Paystar 5070; TrEngine: , 290 Cummins; Tools/Other Options: 13 speed transmission with 3TA Fuller auxillary. Bean Injection Pump with jet tank. Fully rebuilt, customized and refurbished, 23' Kelly, 2'6" Little Giant Swivel, 7-1/2" 2000 rotary table, 1250 air-clutched draw-works, hydraulic pull-down, soap tank, 2 air clutched hydraulic leveling jacks, pipie rack with slide, Imron paint.

Rotary #1423

Badger 1250 Compressor: 100 S-1 LeRoi; Mud Pump: 5X6 Duplex; Mounted On: Ford 9000; TrEngine: , 290 Cummins; Tools/Other Options: Big Cam engine, full overhauled, low hours, 13 speed transmission with 3TA fuller auxillary, new clutch. Bean Inj. Pump with jet tank. Fully rebuilt & customized MUD & AIR COMBO RIG. 2-1/2" Little Giant swivel, 23' kelly, 7-1/2" 2000 rotary table, 1250 air clutched draw works, hydraulic pull down system, 3 leveling jacks (front & rear), pipe rack with slide, Imron paint.
Rebuilt in 2006, option to mount 256 LeRoi Compressor with new clutch if needed.

Auger #1414

Mobile B-61 Year: Ford 300 6 cyl; Mounted On: Int. Paystar S 1900 4X4; TrEngine: Cat; Tools/Other Options: Cat Head, 2 auger racks, 4 sped rotary transmission, heavy duty right angled drive gear box on rotary, power steering, 2 leveling jacks, 10:00 X 20 tires.

No

Picture

Available

Auger #1409

Mobile B 40 22L Year: 1982; Compressor: 375 x 200; Mud Pump: 5 x 6 GD; Mounted On: Ford; TrEngine: 1982, 3208 Cat; Tools/Other Options: sand line, wire line, hoist line, cat head, slide base, top head drive, rod rack, grout pump, 4 jacks, cat pump.

No

Picture

Available

Cable #1407

Bucyrus Erie 22 W.

Rotary #1406

DSI Quickdrill Year: 1978; Compressor: 250 x 125; Mud Pump: 5 x 6 GD; Mounted On: Ford; TrEngine: 1978, 3208; Tools/Other Options: 200' drill rod, all slip and bushings.

March 07, 2008

Rotary #1397

Reichdrill T-650 W11 Year: 1998 525 Cummins; Compressor: 900-350 Sullair; Mounted On: Ford Louisville; TrEngine: 1998, 300 Cummins; Tools/Other Options: 20 gal water injection, 400' drill rod.3,500 hrs on rig.

No

Picture

Available

Rotary #1399

Reichdrill T-650 W 11 Year: 2003 400 cat; Compressor: 900-350; Mounted On: Mack; TrEngine: 2003, 475; Tools/Other Options: 300' drill rods.

Rotary #1405

Mayhew 1000; Mud Pump: 5 x 6 GD; Mounted On: GMC; TrEngine: 1986, 3208; Tools/Other Options: 300' drill rods 2 3/8 , table rebuilt. 6 speed.

Rotary #1404

Failing 1250 Year: 1978 ; Compressor: 5 x 8 1/2; Mounted On: miltary awd; TrEngine: 1973, 250 cumm; Tools/Other Options: 5 speed, new sprockets and chains, new clutch, new table.

Rotary #1403

Ingersoll Rand T-4 Year: 1984 detroit; Compressor: 900-300; Mounted On: CCC; TrEngine: 1984; Tools/Other Options: 6" used hammer and 8" HAMMER, 300' DRILL ROD.

Rotary #1402

Ingersoll Rand TH-60 Year: 1979; Compressor: 600-250; Mud Pump: 3 x 4; Mounted On: Int; TrEngine: 1979, ; Tools/Other Options: 300' drill rod.

Rotary #1401

Ingersoll Rand T-3 Year: 1988 855 cumm; Compressor: 900-350; Mud Pump: wilden mud; Mounted On: Ford 9000; TrEngine: 1988, L 10 300 cumm; Tools/Other Options: 300' drill rod.

No

Picture

Available

Auger #1400

CME 45 Mounted On: Morka buggy; Tools/Other Options: Auto hammer.

No

Picture

Available

Rotary #1398

Chicago Pneumatic T-672 Year: 1974; Compressor: 600 x 250 GHH; Mounted On: GMC; TrEngine: 1974, 6v54 detroit; Tools/Other Options: Heavy hoist, ex mast, 300' drill rod.

February 12, 2008

Rotary #1395

Gardner Denver 1000 Year: 1980; Compressor: G.D. 500 x 250; Mud Pump: 5 x 6 G.D.; Mounted On: Ford 8000; TrEngine: 1977; Tools/Other Options: Chain pulldown. Complete drilling pkg.
340' 2-3/8" X2-7/8" drill rods, 2-7/8" tool joint with bits & subs. 350 gallon al mud tub. All kinds of misc tools, pipe wrenches, hand & air
VEHICLES:
1990 Ford 8000 water truck w/ 1500 gal tank
1999 Ford Ranger XLT 4X4 a/c am/fm cassette
1998 Chevy Silverado 4X4 a/c am/fm al tool bxs
1996 Dodge 1500 4X4 needs work/runs
2310 Ditch witch with trailer
Other Equipment:
2 pressure washers (1 new 1 used)
Drill Press, new 20 ton press band, (2) 2" Honda gas pumps, (1) 2" veramatic diaphgram pump, (1) Honda air compressor, (2) new welders, (1) 220 elec shop arc welder (1) wire feed 140, 50 gallon fuel tnk with elec. transfer
Too much more to list..

Rotary #1396

Ingersoll Rand T-3 Year: 1974; Compressor: 750-250; Mounted On: CCC; TrEngine: 1974, 501 gas; Tools/Other Options: 200' 4 1/2" x 25' drill rods, 3 6"hammers, spare air 450 x 350 truck mounted, rod truck, very good strter rig.

January 29, 2008

Rotary #1393

Gardner Denver 2000 Year: 1977;Mounted On: Kenthworth; TrEngine: 1977, 400 cumm; Tools/Other Options: 18 " rotary table, double drum, king swivel, kelly 4" x 38', air controls, pulldown, jacks, engine rebuilt.

Rotary #1392

Gardner Denver 1500 Year: 1977; Compressor: WEJ 750 x 350; Mud Pump: 5 1/2 x 10 mud; Mounted On: Mack; TrEngine: 1977, 350 cummins; Tools/Other Options: break out tongs, 40 drtill rods 4 1/2 x 40' long tower.

Rotary #1394

Speedstar SD 30 Year: 2005; Mud Pump: 5 x 6 GD; Mounted On: Int 7400; TrEngine: 2005, DT 466; Tools/Other Options: Sand separator, top head with jib controls on both sides. Front and rear jacks, 10 29' rods with 2 subs, mud pan, breakout wrench.

No

Picture

Available

Rotary #1391

Speedstar SD-200 Year: 1988; Compressor: 250-300; Mud Pump: wieland; Mounted On: Int. 1800; TrEngine: 1988, Cumm; Tools/Other Options: 600' 3" x 20'.

January 16, 2008

Rotary #1390

Failing CF-15; Compressor: 100 SDI Leroi; Mud Pump: 5 x 6 G.D. Rebuilt; Mounted On: Int. Loadstar 1850; TrEngine: 1977, 466; Tools/Other Options: 7 1/2 retractable table, new pulldown chains, new bearings in pulldown shaft, 38' mast, 3 jacks, new kelly with extra kelly, mud pump rebuilt.sandline drum, 466 truck engine rebuilt, new pinion in table.

Rotary #1389

Reichdrill T-650 Year: 1985 3406 Cat; Compressor: 825 x 300 GHH; Mounted On: Int. 2574; TrEngine: 1985, 300 cummins; Tools/Other Options: Heavy hoist package 50 k pullback, 300' drill rod, 160 chain, big pulldown cyl. 9 gpm water injection, electric oiler, brand new rotation/hoist/rapid valves and sub plate. Ready to drill.

Rotary #1387

Speedstar SD 30 Year: 1996; Compressor: 200 x 100 Sullair; Mud Pump: 5 x 6 GD; Mounted On: Int.; TrEngine: 1995, DT 466; Tools/Other Options: 10,000 hrs on rig, rebuilt top head, single axel, rebuilt 5 x 6 mud pump, new winch line cable, spare top head, new transfer case, 9 gal water injection pump, 200 gal water tank, tool boxes.

No

Picture

Available

Rotary #1386

Cyclone 35 R combo Year: 1964; Mud Pump: 5 x 6 GD; Mounted On: IHC; TrEngine: 1992, DT 466; Tools/Other Options: Tandem axel, 28' mast, 15' Kelly, Hydraulic pulldown, 235' of 2 7/8 x 2 3/8 FE thread drill rod, 14' drill stem and drive clamp, 4 1/4 retractable table, 3 jacks, 2 ford industrial motors both rebuilt, 3' by 6' mud pan, 330' drill cable 6 months old, 5 x 6 GD mud pump, (fluid end 75%).

November 19, 2007

Rotary #1385

Mayhew 1000 Year: pto; Compressor: Leroi 50 si; Mud Pump: 5 x 6 GD; Mounted On: Mack; TrEngine: 1977, 300 HP diesel; Tools/Other Options: 23' ft kelly 3 5/16,20' rod box, 7 1/2 no retractable table, new hyd pulldown-motor and pump, new bearings in turntable and seals, new 2" little giant swive, new bearing and seals in draw works, new cable both lines, 5 x 6 mud just rebuilt.

November 06, 2007

No

Picture

Available

Rotary #1384

Reichdrill T-650-W 11 Year: 1998; Mounted On: Freightlinner; TrEngine: 1998.

Auger #1375

Simco 2400 Year: 1987 3 cyl. Deutz diesel; Mud Pump: dual hyd pump; Mounted On: F-450 4 x 4; TrEngine: 2003, 6.0 turbo diesel; Tools/Other Options: cathead, 140 lb hammer, 100 gal water tank, 20' derrick, front hyd jacks, manual reae jacks, auger and rod racks, 2 tool boxes mounted underneath chassis.

October 25, 2007

Rotary #1382

DSI Quickdrill Year: 1978; Compressor: 220 x 125; Mud Pump: 5 x 6; Mounted On: Ford F-7000; TrEngine: 1978, 3408; Tools/Other Options: 260' drill rods, dual head motor, 6" hammer.

October 11, 2007

Rotary #1380

Simco 5000 Year: 1979; Mud Pump: 4 x 3; Mounted On: Ford; TrEngine: 1979, 300 Ci ford; Tools/Other Options: 2 winches, grout pump, 265' drill rods 2 3/8 x 15', 2 rear jacks, tandem Axel.

Rotary #1377

Foremost DR-24 Year: 1997 PTO; Compressor: Sullair 900-350; Mud Pump: ; Mounted On: Wester Star; TrEngine: 1997, Cat 3406; Tools/Other Options: Air conditioning, 20,000 lb frt axel, 46,000 rr. Jake brake, sandline 6,000 lb winch, cat 12 gal 600 psi water pump, 4.2 gal venturi type oiler, 30,000 lb pulldown, 58,000 lb pullback, regen circurt for rapid, 4 1/2 breakout wrenck, top drive assy. DR - 24 lower drive, vandal covers, swivel discharge assy, 10".many spare parts.

Miscellaneous #1379

Smeal 5-T Mounted On: Chevy 3500; TrEngine: 1995, 6.5 Turbo Diesel; Tools/Other Options: new clutch, new injection pump. 5 speed manual, 126K miles.

No

Picture

Available

Auger #1375

Simco 2400 Year: 1987 3 cyl. Deutz diesel; Mud Pump: dual hyd pump; Mounted On: F-450 4 x 4; TrEngine: 2003, 6.0 turbo diesel; Tools/Other Options: cathead, 140 lb hammer, 100 gal water tank, 20' derrick, front hyd jacks, manual reae jacks, auger and rod racks, 2 tool boxes mounted underneath chassis.

No

Picture

Available

Auger #1374

Mobile B-53 Mounted On: Ford 800; TrEngine: 1992, Diesel; Tools/Other Options: Truck has 116,000 miles, air brakes. Rig has new PTO. Condition: Good.

September 02, 2007

Auger #1364

Diedrich D-120 Year: 1994; Mud Pump: 3 L 8; Mounted On: GMC topkick; TrEngine: 1994, Cat 3116; Tools/Other Options: double auger rack, 10,000 and 3,500 lbs winches, 500 gal water.

Cable #1371

Bucyrus Erie 24L Year: Continental 6 cyl; Mounted On: Ford F-700; TrEngine: 1980, 370 gas; Tools/Other Options: Drill is early 50's, Red Seal engine, new trident chatter hammer drill stem, everything ran good when parked 10 years ago. Gas engine on truck needs work. Tools include: breakout wrenches, drive clamps, pulling cap, drilling and pulling jars, torpedo, fishing tools, 2 sets of sheaves. May need cable.. Condition: avg for age.

Rotary #1373

Bucyrus Erie 20W Year: 4 cyl; Mounted On: GMC; TrEngine: 1976, ; Tools/Other Options: 3 line machine, new jack shaft, bushings and clutches. New friction wheels for mast and bailer, rebuilt all 3 sheaves, rebuilt mag. Hercules drill engine, tools for 6". New paint. Rig and truck run great. Condition: avg.

Cable #1372

Bucyrus Erie 24W; 6 cyl Int.; Mounted On: F-750; TrEngine: 1978, ; Tools/Other Options: Friction wheel bailer, some tooling included, new drill stem, new trident hydrolifted sub. Condition: avg for age.

Cable #1370

Bucyrus Erie 60L Year: Buda 6 Cyl propane; Mounted On: GMC 6500; TrEngine: 1978, 427CI V8; Tools/Other Options: New paint on truck and rig. All necessary drilling and bailing tools included except for jars. New rear manual outriggers.

No

Picture

Available

Rotary #1369

Speedstar SS-10 Year: 1980 ; Compressor: 100 SDS Leroi; Mud Pump: 5 x 6 GD; Mounted On: Ford L 8000; TrEngine: , Cummins 325 hp; Tools/Other Options: chain pulldown, 8" retractable rotary table, air clutches, air throttle, 35' derrick, breakout tongs.

August 21, 2007

Rotary #1358

Chicago Pneumatic T-650 Year: 1977 cat 3406; Compressor: 825 x 300 GHH; Mounted On: Ford 8000; TrEngine: 1977, 3208; Tools/Other Options: 300' drill rod.

Rotary #1368

Quickdrill Year: 1979; Compressor: leroi 175-100; Mud Pump: 5 x 6 GD; Mounted On: Ford; TrEngine: 1979; Tools/Other Options: 200' drill rod 2 7/8 x 20'.

Rotary #1359

Reichdrill T-650 Year: 1985 3406 DITA; Compressor: 825-300; Mounted On: Int 2574; TrEngine: 1985, 300 Cummins; Tools/Other Options: 300' drill rods 4 1/2 x 20', heavy hoist (50,000).

Rotary #1353

Speedstar SS 15 111 Year: 1979; Compressor: 500 x 250 leroi; Mud Pump: 3 x 4; Mounted On: GMC General; TrEngine: 1979, 290 Cumm; Tools/Other Options: top head, 300' 3 1/2 x 2 3/8 20' drill rods, stablizers and bits.

Rotary #1367

Speedstar SS 15 111; Mud Pump: 2 mission 4x3x13 mud pump; Mounted On: Int.; TrEngine: 1991, Cummins; Tools/Other Options: 7.5 Mckissick block, 8" retractable table, 22' fluted kelly, 3" swivel, 40' mast, 4 jacks, reverse air capable, rod spinner, 600' 3 1/2 if x 20' drill rod, completely rebuilt.

Rotary #1369

Speedstar SS-10 Year: 1980; Compressor: 100 SDS Leroi; Mud Pump: 5 x 6 GD; Mounted On: Ford L 8000; TrEngine: , Cummins 325 hp; Tools/Other Options: chain pulldown, 8" retractable rotary table, air clutches, air throttle, 35' derrick, breakout tongs.

No

Picture

Available

Rotary #1366

Speedstar SS 135; Compressor: Development; Mud Pump: 5 x 6 GD; Mounted On: Ford F 750; TrEngine: 1988, diesel; Tools/Other Options: 300' of 15' drill rod, 8 1/2 table, rod rack.

August 01, 2007

Rotary #1363

Mayhew 500.

No

Picture

Available

Auger #1362

CME 75 Year: 1992; Mud Pump: 3 L 8 moyno; Mounted On: not mounted; Tools/Other Options: auto auger rack, 140 lb auto hammer, slide base/ with wiggle tail, 10,000 and 3,500 lbs winches.

No

Picture

Available

Auger #1361

CME 75 Year: 1993; Mud Pump: 3 L 8; Mounted On: 1993 INT; TrEngine: 1993, 6 cyl cummins; Tools/Other Options: high torque 6 cyl cummins.

Rotary #1365

Chicago Pneumatic

Rotary #1357

Reichdrill T-650 W Year: 1995 3406; Compressor: 840-350; Mounted On: Ford; TrEngine: 1995; Tools/Other Options: 300' drill rod.

No

Picture

Available

Rotary #1356

Simco 2800.

Rotary #1350

Drilltech D 60 K !! Year: 1985; Compressor: 1250 cfm x 150 psi; Mud Pump: 510 P oil well mud pump; Mounted On: trailer mounted; Tools/Other Options: pipe loading arm, hobart welder and 15,000 watt generator mounted on deck, 3,000' of 4 1/2 drill rods, pipe trailer, hyd pipe racks, dog house with 1250 gal fuel tank on front, 1979 Mack winch truck with rolling tail board.

Rotary #1355

Deeprock DR 150 Year: 2003; Mud Pump: Rupp mud piston pump; Mounted On: Ford F 750 4 x 4; TrEngine: 2003, 5.9 cummins; Tools/Other Options: tophead travel 11' 4 ", pulldown 12,000 lbs, pullback 16,000 lbs, variable hydrostatic, high (all speeds) 420 hrs on rig.top head swivel with 2" water course. 300' mayhew jrs 10' auto rod handling system.

Rotary #1360

Drilltech D 25 K !! Year: 1983; Compressor: 750-250; Mounted On: CCC; Tools/Other Options: 300' drill rod.

No

Picture

Available

Water Truck #1354

1978; 2000 gallon water.

Water Truck #1352

Year: 1990 Mounted On: IH 4900; TrEngine: 1990; Tools/Other Options: 1100 gal wateer, 100 gal fuel, with electric pump. Rear winch for pipe handling, miller bobcat welder.

No

Picture

Available

Water Truck #1349

Smeal 5-T Year: 1985; Mounted On: gooseneck trailer; Tools/Other Options: very little use, like new, hydraulic jacks, pipe rack, remote control.

July 20, 2007

Rotary #1348

Bucyrus Erie 20W; mounted on 2000 GMC with new 454 engine, Hyd Jacks.

July 16, 2007

Rotary #1346

Speedstar SS 5 Year: 1977; Mud Pump: 4 1/2 x 5 GD; Mounted On: Ford; TrEngine: 1977, Diesel; Tools/Other Options: 270' 2" IF drill rod.

June 22, 2007

No

Picture

Available

Cable #1336

Bucyrus Erie 22 W series 111 Contiental; Mounted On: GMC 7000; TrEngine: 1990, 366 big block; Tools/Other Options: hyraulic derrick, and jacks.

June 19, 2007

Rotary #1347

Mayhew 500 Mud Pump: 5 x 6 GD; Tools/Other Options: 5 1/4 retractable table with hyd. Cylinders, 20' drill rods, double drum w/mechanical clutches, 4 hyd jacks, two traveling blocks sheave, little giant 2" swivel, 23' flutted kelly with saber sub back to 2 7/8 If , breakout tongs, 26 joints of 2 3/8 if drill pipe, drill pipe trailer and water truck also available at extra cost.

May 22, 2007

Rotary #1344

Jaswell 2400 Year: 199; Compressor: 1050-350; Mounted On: Int; TrEngine: 1991; Tools/Other Options: 1000 drill rod.

Rotary #1343

Jaswell 150 Year: 1991 Det; Compressor: 950-350; Mounted On: Int.; TrEngine: 1991, Dt 46.

No

Picture

Available

Rotary #1345

Chicago Pneumatic T-700 Magnum Year: 1983 Cummins; Compressor: 900-300 Sullair; Mounted On: Four Axel carrier; TrEngine: 1983, Detroit; Tools/Other Options: 6,000' 3 1/2" x 30' drill pipe, 3 jacks, 20 kw generator, deck mounted. Powered by Detroit, Sullair 900cfm @ 350 psi compressor, powered by detroit diesel skid mounted(unit completely refurbished) dog house, 3000 gal fuel tank, soap tank tri-plex soap pump, mounted on tandem axel trailer, all small handling tools for pipe handling, this rig has had extensive refurbishment with in the last 6 months.

May 06, 2007

Auger #1342

Mobile B-61-XD; TrEngine: 1982, 300 6 cyl; Tools/Other Options: 34' mast, 12,000 lb pullmaster winch and 2 nd winch is Koerig 3500, wie line on rig 25,000 miles on rig has seen very little use since new.

April 24, 2007

Water Truck #1339

Ford Year: 1979; Mounted On: Ford; TrEngine: 1979, Diesel; Tools/Other Options: 27,500 GVW diesel with 1000 bgal water flat tank.

Miscellaneous #1340

Mud System. Mud Pump: 5 1/5 x 8 GD; Tools/Other Options: 2000 gal above ground mud system, cummins power, 5 1/2 x 8 GD pump shake, desilter, mixing pump, pickup pump, hyd leveling jacks.

Miscellaneous #1341

Service Truck Mounted On: Ford 250 4 x 4; TrEngine: 1997; Tools/Other Options: Tool boxes up and down.

Rotary #1338

Chicago Pneumatic T-650 WS Year: 1979 3406; Compressor: 825-300; Mounted On: Ford 8000; TrEngine: 1979, 3208.

April 03, 2007

Rotary #1325

Drilltech D-25 Year: 1997 3406 E; Compressor: 900-350; Mounted On: Ford; TrEngine: 1996, 295 ford; Tools/Other Options: 420 4 1/2 x 20', compressor rebuilt 06, truck tran, rebuilt 06.

Rotary #1334

Reichdrill T-650 W 11 Year: 2000 ; Compressor: 840-350; Mounted On: Int; TrEngine: 2000.

Rotary #1335

Chicago Pneumatic T-650 WS Year: 1978 3406; Compressor: 825-300; Mounted On: INT; TrEngine: 1988, L-10 Cummins.

March 27, 2007

Rotary #1333

Chicago Pneumatic RT-2500 Year: 1981; Compressor: 840-350 GHH; Mounted On: Hen; TrEngine: 1981, 300 Cummins; Tools/Other Options: 50' mast, 30' kelly, drill steel 1000' 3 1/2 x 30', 20" table, hopist 70,000 lb, cable and chain auto feed, all small tools, jacks, tires good shape, rig welder, truck cab in good shape, low miles, retractable rotary table, 2 of 4 hyd pumps replaced with new.

Rotary #1331

Davey M-8 Year: GM 4 cyl; Compressor: Davey 400 cf 185; Mounted On: 1974 Ford; TrEngine: , V-8; Tools/Other Options: 4 " kelly 25' , 32' mast, 3/4 line on draw works, 3 jacks.

Rotary #1330

Mayhew 1000 Mud Pump: 3 x 5 mud pump; Mounted On: Int; Tools/Other Options: 2 7/8 x 25' kelly, cat head 16 joint 2 7/8 mayhew jr. by 20'.

No

Picture

Available

Cable #1329

Bucyrus Erie 20 W Year: 4 cyl red field; Mounted On: 1981 Ford; TrEngine: , 360 gas.; Tools/Other Options: 2 man jack rebuilt jack shaft 01, 600' 5/8 drill line 3 line machine.

No

Picture

Available

Cable #1332

Keystone Tools/Other Options: 57' mast, 24 in crown sheave, 3 line machine, 18: chain , 3/8 bail line.

March 21, 2007

Rotary #1327

Reichdrill T-690 Year: 2000 Cat 500 hp; Compressor: 990-350; Mounted On: Freightliner; TrEngine: 2000, 3406 cat; Tools/Other Options: 6 pod loader, 18 gal water inj. 15 piece rod rack, 6 pod loader, 400' drill rod 4 1/2 x 20'.

Auger #1326

CME 75 Year: 1989; Mounted On: Ford 8000; TrEngine: 1989, 5.9 Cummins; Tools/Other Options: 140 lb hammer, rebuilt by CME 11-06, 185k miles, 32 GVW, 50; of 4 1/4 augers.

March 09, 2007

Rotary #1324

Chicago Pneumatic T-700 WH Year: 1978; Compressor: 840-350; TrEngine: 1978; Tools/Other Options: 2,800' drill rods, 39' stroke,slips, bushings.

February 21, 2007

Auger #1323

Mobile B-57 Year: 1987 300 gas 6 cyl; Mud Pump: 3 L 6 monyo; Mounted On: Ford F-700 4 x 4; TrEngine: 1987, 460 gas; Tools/Other Options: 5,000 lb winch, 3 jacks, in/out slide base, hi/lo speed control, hyd breakout wrench, 149 lb hammer with cat head,.quick disconnect mast for low clearance drilling, 400 gal water tank, 3 tool boxes, dual slide auger racks, under rod storage.

Miscellaneous #1320

Smeal 10-T Year: 1977; Mounted On: Chev; TrEngine: 1975, 350 Gas; Tools/Other Options: 2 tanks, good tires, double cat heads, sandline, lighted mast, hyd jacks. 4 speed.

Rotary #1317

Cyclone TH-60-36 Year: 1978; Compressor: Dev 330-130; Mud Pump: 3x4; Mounted On: INT. 1850; TrEngine: 1978, 3208; Tools/Other Options: 240' drill rod, new clutch, casing hammer.

January 29, 2007

Rotary #1316

Challenger 320M Year: 1981 Detroit 8V92NA; Mud Pump: GD 7-1/2" X 10"; Mounted On: 3 Axle Trailer; Tools/Other Options: 380 HP engine, double drum stacked drawwords with PO221 clutches and 8" X 32" double brakes, McKissick 75T three sheave blocks, 18" Howawrd Turner with variable speed from 25 to 250 rpm, 64' derrick rated to 150,000#, Allison 5860 transmission, racking board, block & hook, 3-1/2" ID water course swivel, PARMAC hydromatic brake, catheads, deck mounted mud pump.

Rotary #1315

Speedstar SD50 Year: 1999; Compressor: 300/200 air; Mud Pump: 5X6; Mounted On: Peterbuilt AWD; TrEngine: 1999, Cummings; Tools/Other Options: 2006 - new hydraulics, pumps, mtors, charge pumps. All new gauges in control panel. New injectors, pump and ECM in Cummings in 2005. Rig has approx 7500 hrs, truck has approx 30,000 miles. 580' 2-7/8" rod X 2-3/8" MJ. 5" hammer with casing driving head.
1997 INTERNATIONAL D444T TRUCK WITH 1000 GAL POLY TANK. 100 GAL FUEL TANK with electric fuel transfer pump. 2005 MILLER 225 WELDER 8500 watts
Equipment runs daily. Condition: Good.

No

Picture

Available

Rotary #1314

Speedstar 150 Mounted On: CCC 4 x 4; Tools/Other Options: 150,000 lb pullback.

Rotary #1308

Reichdrill T-650-WII Year: 2003 500 Cat 3406C; Compressor: 1000/350 Sullair; Mounted On: Mack Granite 6X4; TrEngine: 2003, Mack 427 diesel; Tools/Other Options: 34' Mast with 28' stroke, 18" table opening, 7000# winch, 3 leveling jacks, 15 pc. Rod box, 9 pod bbl loader, 20 gpm water injection pump, aux. blowdown system, 8 gallon air line.lubricator, 300' 4" X 20' drill pipe, 2-7/8" thread. Fuller RTO transmission, jake brake.

January 02, 2007

Miscellaneous #1312

Gus Pech Super George Year: 1978 2006 JD 6068; Mounted On: Int. 6X4 Model 4900; TrEngine: 1990; Tools/Other Options: 494 hrs on John Deere drill engine. Truck is a 13 speed with air brakes, miles = 393,433. 90' Kelly Bar 3-1/2", 52" turn table, 2005 Front position hydraulic jacks, 2004 Braden winch, Working condition.

Cable #1311

Brewster Mounted On: International; TrEngine: 1986, 466 Diesel; Tools/Other Options: Double Drum, Double Pole, 60' Mast.

Auger #1310

Simco 2400 SK-1 Year: 1988 Wisconsin VH4D; Mounted On: Simco Model 3600 Trailer; Tools/Other Options: 24 HP air cooled 4 cyl. Gas engine. 5' Stroke, 15' Mast, Cathead, 14